Free

LED Dimmability Checker

Check if your LED bulbs are compatible with your dimmer switch. Avoid flickering, buzzing, and other common dimming issues.

Check Your Setup

Total Wattage:40W
Assumed Minimum Load:10W ✓

Dimmer Type Compatibility

Leading Edge (TRIAC)LIMITED

Traditional incandescent dimmers. May cause flickering with LEDs.

Trailing Edge (ELV)GOOD

Better for LEDs. Smoother dimming with less flicker.

0-10VEXCELLENT

Professional-grade. Best compatibility with commercial LED fixtures.

PWM (Pulse Width Modulation)EXCELLENT

Digital control. Ideal for LED strips and smart lighting.

Smart Dimmer (WiFi/Zigbee)EXCELLENT

App-controlled. Usually designed specifically for LEDs.

Common Dimming Issues & Solutions

IssueCauseSolution
FlickeringIncompatible dimmer type or minimum load not metUse trailing-edge dimmer or add dummy load
BuzzingElectrical interference from dimmerSwitch to LED-rated dimmer with proper shielding
Limited rangeDimmer minimum is too high for LEDUse dimmer with lower minimum setting (1-5%)
Drop-outLED turns off before reaching minimumAdjust dimmer calibration or use compatible dimmer
Pop-onLED jumps to brightness instead of smooth startUse soft-start dimmer designed for LEDs

How this checker scores your setup

  1. Start from a base score for the dimmer type: excellent 95, good 75, limited 50.
  2. Total load = bulb watts × number of bulbs. The checker assumes a minimum load of 25 W for leading-edge dimmers and 10 W for the others; below that, subtract 30.
  3. CFL bulbs: subtract 20 from the LED score.
  4. Incandescent and halogen bulbs are the load phase-cut dimmers were designed for: on leading-edge, trailing-edge and smart dimmers they start from 95, minus 30 if the load is below the assumed minimum. On 0-10V and PWM, which are control inputs on LED drivers and ballasts, the checker shows "Not applicable" instead of a score.
  5. The score is kept between 0 and 100. It is a point score, not a percentage chance that the pairing works.
  6. Labels: 70 and above "Likely compatible", 40 to 69 "May have issues", below 40 "Likely incompatible".

Are all LED bulbs dimmable?

No. Only bulbs marked dimmable on the packaging or datasheet are designed to work on a dimmer. This checker cannot tell whether your bulb is dimmable; it assumes it is and scores the dimmer type and the connected load.

Why do LED bulbs flicker or buzz on an older dimmer?

Leading-edge dimmers were designed for incandescent loads of tens or hundreds of watts. A few LED bulbs often add up to less than the dimmer's minimum load, and the dimmer then cannot switch cleanly. This checker assumes a 25 W minimum for leading-edge dimmers and 10 W for the other types; the real figure is printed on your dimmer or in its instructions.

What is the difference between leading-edge and trailing-edge dimmers?

Both chop the mains waveform. A leading-edge (TRIAC) dimmer cuts the start of each half-cycle, and a trailing-edge dimmer cuts the end, which is gentler on the electronic drivers in LED bulbs. That is why this checker starts trailing-edge dimmers from a higher score.

How do I confirm a bulb and dimmer will work together?

Look the bulb up in the dimmer maker's LED compatibility list, or the dimmer in the bulb maker's list. Those lists name specific bulb and dimmer models; this checker's score is a screening estimate and does not replace them.

Worked example: LED bulbs on a leading-edge dimmer

Computed by this calculator's own code (method v1.1.0) when this page was built on 2026-11-20.

Inputs
Setup A4 × 10 W LED, leading-edge
Setup B4 × 5 W LED, leading-edge
Setup C4 × 5 W LED, trailing-edge
Results
A40 W load (minimum 25 W), score 50
B20 W load (minimum 25 W), score 20
C20 W load (minimum 10 W), score 75

The same 20 W of LEDs falls below a leading-edge dimmer's assumed minimum but clears a trailing-edge dimmer's.

Every score this checker can give

Dimmer typeAssumed minimum loadLED, load metLED, load not metCFL, load metCFL, load not metIncandescent or halogen, load metIncandescent or halogen, load not met
Leading edge (TRIAC)25 W50203009565
Trailing edge (ELV)10 W754555259565
0-10V10 W95657545Not applicableNot applicable
PWM10 W95657545Not applicableNot applicable
Smart dimmer10 W956575459565

The checker has only three inputs that change the score: dimmer type, whether the total load reaches the assumed minimum, and the bulb type. Two setups with the same three answers always get the same score. CFL scores assume a CFL marked dimmable.

Assumptions and limits

  • The score is a rough screening aid, not a compatibility test. The dimmer maker's LED compatibility list is the reference.
  • The checker does not know your bulb or driver model. It cannot tell whether a driver accepts phase-cut, 0-10V or PWM control, so a high score for 0-10V or PWM only applies when the fixture's driver has that control input.
  • Maximum dimmer load, inrush current and the number of lamps a dimmer maker allows for LED are not checked.
  • Minimum loads vary by dimmer model; the 25 W and 10 W figures are assumptions of this checker. Check your dimmer's datasheet.
  • The bulb must be marked dimmable; a non-dimmable LED should not be used on any dimmer.
  • Smart dimmers are treated as mains phase-cut wall dimmers. Halogen means a mains-voltage halogen lamp; low-voltage halogen on a transformer is not modelled.

Sources

  • Dimmer and lamp datasheets (minimum load and compatibility lists) are the authority for a specific product.